Bisalloy Steel Group
Global (EN) Change

Solving The Survivability Dilemma With Bisalloy® High Hardness Armour Steel

Working on a protected vehicle program presents a core challenge: how do you balance the trade-off between protection and weight?

The fact that no Australian life has ever been lost in a Bushmaster is not a coincidence: it’s a consequence of design choices that began with material selection long before deployment, providing protection, mobility and ultimately, survivability when it matters most.

Choice of material cascades through every design decision on the program. More armour means more mass. More mass means slower speeds, shorter range, more stress on suspension and drivetrains. And critically, less weight budget for active protection systems, electronics, and sensors that increasingly define how modern armoured vehicles perform in the field.

Every tonne of unnecessary armour mass is, effectively, a tonne of capability that never makes it onto the vehicle.

Survivability = Protection × Mobility

This core equation establishes the primary goal for every protected vehicle program: success depends on achieving high performance in both factors. Material selection, particularly the grade of armour steel specified for the hull, is one of the highest-leverage decisions on any vehicle platform program. 

While protection is the vehicle’s capacity for threat defeat and crew safety, measured by technical criteria like V50 and certification standards, mobility covers the vehicle’s core operational capability: its range, speed, load capacity, and the design margin available for integrating modern systems like Active Protection Systems (APS) and advanced electronics.

These two factors are interdependent: if a vehicle achieves maximum armour but is too heavy to move or operate its systems effectively, its overall survivability collapses. When a program focuses solely on increasing protection at the expense of mobility, the final outcome is counterproductive. The choice of armour steel grade is the most significant upstream decision because it determines whether the design accepts a forced and false choice, or is set up to overcome it. 

High Hardness Armour (HHA) delivers the structural freedom necessary to elevate both protection and mobility, which ultimately increase survivability when it matters most.

RHA puts programs under pressure from day one

Rolled Homogenous Armour (RHA) has been the baseline of armoured vehicle design for generations. It’s well understood, well tested, and widely certified. But its ballistic performance-to-weight ratio creates structural pressure from the outset.

To meet protection thresholds against threats like 7.62mm Armour Piercing (AP), RHA requires greater section thickness. That thickness adds mass directly to the hull and structural elements, and the issues compound: less payload capacity, degraded mobility, and reduced headroom for the systems that define modern armoured vehicle capability. 

The question isn’t whether armour steel grade selection matters. It clearly does. The question is how you solve the survivability equation at the specification stage: before the weight budget is already spent and the compromises are locked in.

BISALLOY® Armour HHA500: same protection, lower weight

BISALLOY® Armour HHA500 is a High Hardness Armour grade engineered to deliver equivalent or superior ballistic protection to RHA at meaningfully reduced section thickness, which translates directly into a lighter hull structure.

The numbers make the differences crystal clear:

PropertyRHABISALLOY® HHA500Change
Thickness (7.62mm AP protection)23 mm19 mm−17%
Areal density (kg/m²)181 kg/m²149 kg/m²−18%
V50 (7.62mm AP, m/s)830 m/s845 m/s+2%
Hardness (HB)280–320 HB480–540 HB+65%
Table 1: BISALLOY® Armour HHA500 vs Rolled Homogeneous Armour (RHA). All grades designed and tested to STANAG 4569 and MIL-DTL-46100.

At 19mm versus 23mm for 7.62mm AP protection, HHA500 achieves equivalent threat defeat at an 18% reduction in areal density. Across a full hull structure, this translates to a structural weight saving of 15–25% depending on platform geometry and configuration.

The V50 improvement of +2% means HHA500 does not merely match RHA protection: it exceeds it at reduced thickness, giving you margin when working to STANAG 4569 Level 3/4 or MIL-DTL-46100 certification requirements.

BISALLOY® Armour and Structural Steel: Proven in the field

Since the 1990s, Australia’s protected mobility platforms, including the Bushmaster Protected Mobility Vehicle, have relied on BISALLOY® Armour and Structural Steel to bring soldiers home safely. In over two decades of operational service, including IED strikes in Afghanistan, no Australian life has ever been lost inside a Bushmaster. 

In 2010, a Bushmaster crew survived an IED strike in Afghanistan. When those same soldiers were reunited with their damaged vehicle at the Australian War Memorial in 2025, the reality of that engineering was captured in a single sentence from one of the survivors: “I owe my life to that vehicle.”

The materials you specify at design stage determine whether a vehicle protects its crew at the moment it matters most.

What the weight savings make possible

The mass savings delivered by HHA500 don’t simply reduce gross vehicle weight: they create a weight dividend you can deploy strategically across the platform.

In one light armoured vehicle program using BISALLOY® Armour HHA500:

23% Overall hull weight saved+18% Operational radius gain on a single fuel load+ Additional spall liners added within saved weight budget

“In programs where engineers have switched to HHA500, we typically see hull weight savings in the range of 23%. In one case, that headroom allowed the integration of spall liners that weren’t previously viable, and delivered an 18% increase in operational radius on a single fuel load. For extended patrol missions, that kind of gain is decisive.”

Justin Suwart, Bisalloy Steels, Armour Business Development Manager

The BISALLOY® Armour grade range

Beyond HHA500, Bisalloy offers a full range of high hardness armour grades to address different threat levels and program requirements, including VHH550 (Very High Hardness) and UHH600 (Ultra High Hardness) for applications requiring add-on armour modules or enhanced protection against advanced AP threats.

All grades are manufactured in Australia under ISO 9001, 14001, and 45001 safety, environment and quality management systems, with full material traceability from melt to plate. For program managers working within Australian, Five Eyes, or NATO procurement frameworks, that traceability, and the sovereign supply chain it represents, is increasingly a program requirement in its own right, not a nice-to-have.

Need help with armour grade selection?

Talk to the Bisalloy Defence team about armour grade selection, material certification, and design integration support for your platform program.

bisalloy.com/australia/contact-us/